Controlling a British Gas WR1 Receiver with an Arduino

Over the holiday season I started looking at whether my boiler, a Worcester Bosch Greenstar 28i, was compatible with the Nest thermostat. After some Googling I began to wonder whether I could make my own controller and began investigating how the existing wireless programmer might function. The programmer currently in use is a British Gas WR1, which looks to be a re-branded Drayton Digistat device.

British Gas WR1

After removing the programmer from its wall mounting plate I immediately noticed a sticker indicating it operated using 433MHz. Thankfully this is part of the unlicensed spectrum meaning transmitters are likely to be readily available. Sure enough, there are 433MHz transmitter/receiver pairs available in the UK for just £2 on eBay. I immediately bought myself an Arduino, some cables, a breadboard and waited eagerly for everything to arrive.

My plan was to create a single channel logic analyser as described in Steven Hale’s excellent blog post, using the soundcard in my laptop to capture what my existing programmer transmits. My soldering ability leaves a lot to be desired, so I’ll spare you a photo and include a diagram that is likely to be much more useful:
Sound card logic analyser

With my logic analyser built I then proceeded to install Audacity and begin trying to record the data sent by my wireless programmer. I started recording and turned up the heating, it was immediately apparent that something had recorded as once transmission completed there was a 100ms radio silence:

Audacity Recording Screenshot 1

According to the Steven Hale, the same person who provided the details for creating the logic analyser, these little 433MHz radios have gain control – once they detect nothing they try to boost the signal which is why we get the 100ms radio silence and then noise. If you try to reproduce this recording, you are looking for three repeats of the same transmission. Since the wireless programmer has no receive capability it must blindly transmit and hope for the best, so it does this three times.

To make things a bit easier it’s best to set Audacity to use 192KHz sampling (bottom right, set “project rate”). You’ll also want to view the track as a waveform (click the down arrow by the words “Audio track” and select “Waveform (dB)”.

Zooming in yet further I could finally see the transmission data:

Audacity Recording Screenshot 2

The next step was to count the number of samples to determine how long I needed my radio to transmit for, requiring yet more zooming.

in and selecting a portion of the on/off state. I counted the number of samples and repeated this until the 100ms of radio silence at the end:

Audacity Recording Screenshot 3

I then multiplied these values by 5.2083333 to get the number of microseconds (μs). I ended up with 60 values for “heating on” and 62 values for “heating off”. The next step was then to wire up the 433MHz transmitter I bought from eBay to my Arduino and try and reproduce these signals.

Arduino 433MHz radio

I ran some code I wrote in the days leading up to delivery and to my surprise it worked first time, a sample version of this can be found below.

const uint16_t arrOn[] = {
  632, 491, 0,0,0,0 // Put the values you recorded here.
const int nOnLen = sizeof(Heating::arrOn)/sizeof(int);
const uint16_t arrOff[] = {
  1599, 521, 0,0,0,0 // Put the values you recorded here.
const int nOffLen = sizeof(Heating::arrOff)/sizeof(int);
const int nTxPin = 2; // Arduino digital pin you're using for radio data.

* Transmits a signal on the specified PIN according to a pattern described by
* the start[] array.
* @param start[] Array in on/off pairs for how long in microseconds to
* transmit and then wait for. N.B. Microsecond is 1/1,000,000 of a second.
* @param arrLen Lengh of the array - usually sizeof(array)/sizeof(int).
* @param txPin Digital pin the transmitter data pin is connected to.
void transmitArray(const uint16_t start[], int arrLen, int txPin)
  // Loop over objects in an array.
  for(int i = 0; i < arrLen; i = i + 2)
    // Turn on the transmitter
    bitWrite(PORTD, txPin, 1);

    // Wait (transmitting) for the duration specified.

    // Turn of off the transmitter.
    bitWrite(PORTD, txPin, 0);

    // Wait (not transmitting) for the duration specified.

 * The setup() function is called when a sketch starts. Used  to initialize
 * variables, pin modes, start using libraries, etc. The setup function will
 * only run once, after each powerup or reset of the Arduino board.
void setup()
  pinMode(nTxPin, OUTPUT);
  Serial.println("Press 0 to turn off heating");
  Serial.println("Press 1 to turn on heating");


 * The loop() function loops consecutively, allowing the program to change and
 * respond. Used to actively control the Arduino board.
void loop()
  if (Serial.available() > 0)
    int nIncomming =;
    if (nIncomming == 49) // char code for 1
      transmitArray(arrOn, nOnLen, nTxPin);

    if (nIncomming == 48) // char code for 0
      transmitArray(arrOff, nOffLen, nTxPin);

Pressing 0 turns off the heating and 1 will turn it on.

The next steps are to setup an ethernet connection and have the Arduino run some webservices and a temperature sensor, which I can consume from another device.

Published by

Dave Hope

Dave works in IT for a leading UK based retirement developer, in his spare time he enjoys tinkering with technology and rock climbing.

6 thoughts on “Controlling a British Gas WR1 Receiver with an Arduino”

  1. Hey! Thanks for such a great write up and sorry for dragging up an old post but I have a few questions if you wouldn’t mind?

    I have a Worcester Bosch Greenstar 28i too and have been looking to do exactly what you have. I have managed to sniff the signals and produced the 60/62 values. At this point, did you round the figures at all as I have a decimal?

    Secondly, in trying to run up your example code, I get “‘Heating’ has not been declared”. Assuming this is part of a bigger project for you, is there a simple way I can declare it to just get this segment to work?

    As I’m sure you can tell, I’m really new to Arduino but would love to get this working.

    Thanks very much, John

    1. Hi John,

      The heating error, remove “Heating::” from this line:
      const int nOnLen = sizeof(Heating::arrOn)/sizeof(int);

      In terms of the values to send, these should be in microseconds. So you should end up with something like:

      arrOff[] = {
      520,500, 520,500,
      520,500, 520,500,
      520,500, 520,500,
      520,500, 1000,500,...etc

  2. This works great, I sampled my thermostat’s 433 transmission using the Universal Radio Hacker toolkit, worked first time once i’d copied the pulse lengths into the arduino sketch! Brilliant!

    There were a couple tweaks to your sketch needed to compile correctly;

    Line 4 – needed to remove “heating::” from the variable reference.

    This worked well using my Drayton Digistat. Next step is to set this up using MQTT to integrate with the Home Assistant generic thermostat component. Great work, thanks!

    1. Great, glad you’ve got something running. Sorry for the bug in the code, i’d just copied and pasted out from a larger bit and forgot to correct that bit.

  3. Hi, I am reading this post with great interest, as I have been trying to capture the RF send codes using RFLink ( without any luck. I use Home Assistant, where I would like to be able to turn on/off my Worcester Bosch Greenstar 30i, which uses a DT10RF, but I have to admit, I got lost in the middle and the end, with the logic analyser and then Arduino code. If someone could give me some assistance with the logic analyser please, that would be great.

Leave a Reply to Kevin Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.